Glue wing Onto top motor stick Cut 20-in length 1/16in contest rubber such Peck-Polymers Wet ends rubber tie knot pull tight Cut 1/16 sq balsa sticks glue tissue white glue Cutthe motor stick 1/ax 1/4 balsa glue rudder tissue underthe rudder Glue 1/2-in length of1/s square balsa frontof motor stick shown Glue stabilizer motor stick Crack center joint wing dihedral glue prop up matchbook until dry Stick rear rubber hook through motor stick bend over point top apply drop glue over joint 58 Model Aviation just miniature easily built high-perfor -u Complete projeci two pages Ehling-designed AMA Cub mance rubber model Lay waxed paper tissue over plan Smooth tissue hands tape down corners Lift tissue plan cut out parts razor blade scissors Bend rear rubber hook straight pin Fit Skeeter propeller assembly motor stick Finished Baby Cub full-sized AMA Cub designed Frank Ehling Rubber motor winders much faster hand-winding available Sterling Models Gaylord Plastics 16431 9th StSanta Monica CA 90404 $395 Use cooking oil Sig rubber lube rubber make motors last longer allow windsand longer flights STABILIZER GLUE TISSUE SIDE UP TO BOTTOM OF FUSELAGE 1/16 SQ BALSA RUDDER 1/8 X 1/4 BALSA STABILIZER BENT PIN CONSTRUCTION NORTH PACIFIC SKEETER PROPELLER ASSEMBLY 1/8 SQ LAY WAXED PAPER AND TISUE OVERPOWER0-12 LOOP OF 1/16 THE PLAN GLUE THE 1/16 SQ BALSAOR 3/32 CONTEST RUBBER TO THE TISSUE WHEN DRY CUTFROMPECK- POLYMERS OUT WITH SCISSORS BLOCKRO BOX 2498 UP EACH WING TIP 2LA MESA CA 92041 AND GLUE GLUE ON WINC STABILIZER AND RUDDER WING DESIGNED FOR MODEL AVIATION BY FRED REESE V CD CD
Edition: Model Aviation - 1981/04
Page Numbers: 58, 59
Edition: Model Aviation - 1981/04
Page Numbers: 58, 59
Glue wing Onto top motor stick Cut 20-in length 1/16in contest rubber such Peck-Polymers Wet ends rubber tie knot pull tight Cut 1/16 sq balsa sticks glue tissue white glue Cutthe motor stick 1/ax 1/4 balsa glue rudder tissue underthe rudder Glue 1/2-in length of1/s square balsa frontof motor stick shown Glue stabilizer motor stick Crack center joint wing dihedral glue prop up matchbook until dry Stick rear rubber hook through motor stick bend over point top apply drop glue over joint 58 Model Aviation just miniature easily built high-perfor -u Complete projeci two pages Ehling-designed AMA Cub mance rubber model Lay waxed paper tissue over plan Smooth tissue hands tape down corners Lift tissue plan cut out parts razor blade scissors Bend rear rubber hook straight pin Fit Skeeter propeller assembly motor stick Finished Baby Cub full-sized AMA Cub designed Frank Ehling Rubber motor winders much faster hand-winding available Sterling Models Gaylord Plastics 16431 9th StSanta Monica CA 90404 $395 Use cooking oil Sig rubber lube rubber make motors last longer allow windsand longer flights STABILIZER GLUE TISSUE SIDE UP TO BOTTOM OF FUSELAGE 1/16 SQ BALSA RUDDER 1/8 X 1/4 BALSA STABILIZER BENT PIN CONSTRUCTION NORTH PACIFIC SKEETER PROPELLER ASSEMBLY 1/8 SQ LAY WAXED PAPER AND TISUE OVERPOWER0-12 LOOP OF 1/16 THE PLAN GLUE THE 1/16 SQ BALSAOR 3/32 CONTEST RUBBER TO THE TISSUE WHEN DRY CUTFROMPECK- POLYMERS OUT WITH SCISSORS BLOCKRO BOX 2498 UP EACH WING TIP 2LA MESA CA 92041 AND GLUE GLUE ON WINC STABILIZER AND RUDDER WING DESIGNED FOR MODEL AVIATION BY FRED REESE V CD CD
